Copyright © Lexibook 2007 ST050 17/8/07 18:24:54 ST050.indd 1 GB FR ES PT IT DE NL ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS ITALIANO DEUTSCH NEDERLANDS Codes, Códigos, Codici 3-7 8-12 13-17 19-21 22-26 27-32 33-37 38-51 Copyright © Lexibook 2007 ST050.indd 2 17/8/07 18:24:55 Introduction Congratulations! You have just purchased a Lexibook® Universal 5 in 1 Remote Control. Compatible with over 7,000 audio-visual device, this universal remote control combines the functions of several remotes: TV, DVD, Satellite (SAT), Video Recorder (VCR), and Auxiliary (AUX). Digital TV receivers (like ADSL modems, Freeview, DVB-T etc...) can be also controlled by the SAT key. Caution: Before its first use, you must set up the remote control so that it functions with your chosen audio-visual products. To do so, please read these instructions carefully. Using the buttons and functions Once you complete the setup procedure, the Lexibook® Universal 5 in 1 Remote Control will allow you to control the various audio-video devices you have at home. When you use the remote, first select the type of device you wish to use by pressing the corresponding device key (TV, DVD, SAT, VCR or AUX). Aside from the 5 device keys and the macro keys, all other keys on the remote control are only operative if your device also has these functions. For example, the pause key ( ), will work in CD mode but not in TV mode. Installing batteries Before programming and using your remote control, install 2 x AAA/LR03 alkaline batteries (not included). To do so, open the battery compartment located at the back of the remote. Make sure to install the batteries according to the polarity (+/- signs) indicated inside the battery compartment. Close back the battery compartment. TV1 ­ TV selection and set key. AUX ­ Hi-Fi system selection and set key. DVD ­ DVD player selection and set key. SAT ­ Satellite TV receiver selection and set key. VCR ­ VCR selection and set key. Notes: Your remote control will not lose its settings when the batteries are out of power. When changing the batteries, do not press any key on the remote control. Else, the remote control's settings will be affected. M1/M2/M3 ­ Macro keys. LIGHT ­ to enable the backlight. The red (R), green (G), yellow(Y), and blue (B) buttons can have various functions depending on whether your TV set supports these applications. SET ­ to trigger setting mode. 3 Copyright © Lexibook 2007 ST050.indd 3 17/8/07 18:24:56 ENGLISH ENGLISH Set-up There are 3 programming modes: Manual, Quick Search and Automatic Programming. Please always try the manual set-up FIRST, then if no code in the list of brands and models matches your device, try the Quick Search, and only if this one fails, try Automatic Programming. Warning: program one appliance at a time. For example, start by setting your remote to your TV, then to your DVD player... If your device cannot be programmed using manual setup or its code is not in the list, program your remote control using the quick or auto search function. The search function tests all the codes one after another and finds the right one for your device. Quick search This search should be used only if Manual search failed or if the brand or correct model code are missing. 1. Switch on the device to be set to the remote and aim the remote control at the device. - If VCR, insert a cassette. - If SAT, select a program. - If DVD, insert a DVD. 2. Press the SET key followed by the respective device key on your remote control. Hold down both keys. 3. When the LED lights up, release the buttons. 4. Press the SET button again. The LED starts flashing and quick code search starts. 5. In order to trigger the code search you will have to push the POWER key ( ). 5 codes will be transferred. Wait 3 seconds. If nothing happens, press Power again. Each time the power key is pressed, it will look for 5 new different codes during 3 seconds. You may need to press the power key up to 100 times maximum. (approximately 5 minutes). 6. When your device switches off, the correct code has been found. DO NOT press the POWER button again, as this would restart the code search. 7. Press the respective DEVICE button again to exit the current stage. The LED stops blinking and remains solid. 8. Return to your device and switch it ON again (by using original remote control or the device's front panel buttons). 9. In order to fine tune the search within these 5 codes, you must press the power key and wait 2 seconds. If nothing happens, repeat by pressing power again and wait 2 seconds. If your device still does not respond, you should only need to press the power key 5 times in total before your device turns back OFF. 10. When your device switches OFF, the correct code has been found. DO NOT press the POWER button again, as this would re-start the code search. 11. Press the respective DEVICE button to store and exit. The LED turns off. 12. During step 8, SET button can be pressed to return to step 5. Check whether all applications of your device can be operated using the remote control keys. Manual setup 1. Select the device you wish to set (ex.: TV). Search your device's brand in the code list attached. There is a different code list for each of the 5 devices which your remote control can be set to. Mark down the correspondent 3-digit code(s). One brand may have up to 30 codes. You might have to try several of them before finding the one relevant to your model (see hereunder). You will have to repeat the full procedure. 2. Switch on the device to be set to the remote and aim the remote at the device. - If VCR, insert a cassette. - If SAT, select a program. - If DVD, insert a DVD. 3. Press the SET key( SET ).first and hold it down while pressing the respective device key on your remote control, hold both keys down. For example: To program your TV, press first SET and then TV simultaneously. . When the LED (on upper left corner of the unit) lights up, release the keys. 5. Use the numeric keys to enter the 3-digit code applicable for your device. 6. The LED will turn off; setup is completed. 7. Try some keys on your remote to check if they work properly. If they do, your settings were successful: you found the right code. You are now ready to set another device, with the same procedure. 8. If your remote control's keys do not work, you did not find the right code and you need to try the next 3-digit code corresponding to your device's brand in the list: repeat steps 3 to 7, until your device responds correctly to the keys pressed on the remote. Notes: - Press the respective DEVICE button if you wish to stop the manual setup. If no button is pressed for more than 15 seconds, setup ends automatically and the LED goes off. Copyright © Lexibook 2007 ST050.indd 4 17/8/07 18:24:56 Auto search This search should be used only if Quick Search did not work. 1. Turn on the device to be controlled and aim the remote control at the device. 2. Press the respective DEVICE key on your remote control. 3. Press the SET key followed by the POWER button ( ) on your remote control. Hold down both keys until the LED remains solid. Release both keys; the LED starts blinking. The automatic search begins. . 5 codes are transmitted at a time; there is a 5-second period between each transmission, approximately 9 minutes in total. 5. When your device switches off, then the correct code range has been found. 6. Promptly press the respective DEVICE key to auto search within these five codes. 7. Go back to your device and switch it ON again (with original remote or using the front panel buttons). 8. Aim the searching remote to it: when your device switches off, the correct code has been found. 9. Press the respective DEVICE button to stop/store. The LED turns off. 10. During step 5, the SET button can be pressed to return to step 3 Check whether all applications of your device can be operated with the remote control keys. Tips for quick and auto search modes: - Some devices cannot be powered on/off using the remote control. In such case, use the PLAY button instead of POWER to check if the device responds to the remote control. - The search direction can be changed by pressing the CH+/- button. - All the function buttons except POWER and PLAY can be verified without exiting the quick search mode. If no button was pressed for more than 30 seconds, setup stops automatically, the LED goes off. Should your remote control still not work, check the codes list again and repeat the setup procedure (manual or code search) until you find the correct code. Storing your favourite channels and child lock The FavCH key allows you to store your favourite channels or limit the number of channels accessible to your children. The following number of channels can be stored or retrieved using the FavCH button: Channel (1-4-digit numbers) One digit Two digits Three digits Four digits Number of storable channels 15 10 7 6 Storing your favourite channels Example: store channels 02, 38, and 56. 1. Press and hold the SET button and the FavCH button simultaneously until the LED lights up. 2. Then, subsequently press 0 ­ 2 ­ SET ­ 3 ­ 8 ­ SET ­ 5 ­ 6 ­ FavCH. And for 3 digit numbers press 0 ­ 0 ­ 2 ­ SET ­ 0 ­ 3 ­ 8 ­ SET ­ 0 ­ 5 ­ 6 ­ FavCH. Only numerical keys 1-9 can be set. 1 to -digit channel numbers can be stored. Once you have stored your favourite channels, simply press the FavCH button to browse through the channels in the order they were stored and select one of them. To delete the channels from the memory: 1. Simultaneously press and hold the SET button and TV. 2. Then, one after the other, press 9 ­ 2 ­ 0. Child Lock In Child Lock mode, only the following buttons will be operative: POWER VOL+/-, MUTE, DEVICE buttons SET and FavCH. 1. Simultaneously press and hold the SET button and TV. 2. Then, one after the other, press 9 ­ 2 ­ 1. To switch off the child lock mode: 1. Simultaneously press and hold the SET button and TV. 2. Then, one after the other, press 9 ­ 2 ­ 2. To delete the channels from the memory: 1. Simultaneously press and hold the SET button and TV. 2. Then, one after the other, press 9 ­ 2 ­ 0. 5 Copyright © Lexibook 2007 ST050.indd 5 17/8/07 18:24:57 ENGLISH ENGLISH Macro Keys With one of the macro keys, you can operate a series of up to 15 functions by pressing one single key. In other words, you will be able to execute several control commands in the order they were stored by simply pressing the respective MACRO key. Programming the MACRO Key 1. Press and hold the SET button, then press one of the MACRO keys (M1, M2, and M3). When the LED lights up, release the two buttons. 2. Now press the buttons, the application of which you would like to activate successively in the respective order. (Press the SET button to stop the programming mode.) 3. Finally, press the MACRO key again. When procedure is completed, the LED is off. For example: You wish to store the following control command sequence on M1: TV on ­ Switch to TV/VCR ­ VCR on ­ Play ­ Switch to TV. Then, you have to enter : SET + M1 ­ TV ­ POWER ­ TV/VCR ­ VCR ­ POWER ­ PLAY ­ TV ­ M1. If more than 15 control commands have been selected or no button was pressed for more than 30 seconds, programming stops automatically, the LED goes off and the last MACRO settings will be stored. Deleting the settings 1. To delete the MACRO key settings, press and hold the SET button and press the respective MACRO key. 2. When the LED lights up, release the two buttons. 3. Press the MACRO key again. Any control command previously stored is now deleted. Release the 2 buttons. The LED lights up; its flashing indicates the first digit of the code. If the LED does not turn on: digit = 0. 2. To display the second digit, press and hold the SET button and 2 simultaneously. The LED starts flashing. 3. To display the third digit, press and hold the SET and 3 simultaneously. The LED starts flashing. 4. Repeat steps 1-4 to find the codes of the other devices. TV1 Code DVD Code AUX Code VCR Code SAT Code Operational reset Operational reset will erase all the set functions. 1. Simultaneously press and hold the SET button and TV. 2. Then, one after the other, press 9 ­ 9 ­ 0. Back light function 1. Press the LIGHT key to enable/disable the back light function. 2. The initial status is disabled. 3. When the back light function is enabled, press any key and the light will turn on for 5 seconds and will remain on when a key is pressed. . When this function is disabled, the backlight remains off. Note: continuous use of the backlight will exhaust battery power. Noting the programmed code Always write down the 3-digit code for your remote control after running the search and saving the code. This may be useful if you need to reprogram your remote control in the event of accidental cancellation or when you change used batteries. When searching the code, the LED will flash corre ...