E-Mouse User Manual PX1215E-1NAC Before operating the unit, please read this instruction thoroughly, and retain it for future reference. This product contains an internal rechargeable Lithium battery and is not user-serviceable. Please observe the following safety guide to avoid potential harm to the user, the surrounding, and the product: Do not expose the product to extreme heat or flame. The built-in battery may leak or even explode when exposed to extreme heat. Keep the product dry and never immerse it into water or any liquid. Use the product in the temperature between 10 °C and 40 °C (50 °F and 104 °F). The built-in battery will be permanently damaged if exposed to extreme heat (over 45 °C / 113 °F) or extreme cold (under 5 °C / 40 °F). Use only the supplied USB charging cable to charge the battery. Do not disassemble the product under any circumstances. Stop using the product immediately in the event that the product feels hot or battery leakage occurs. Call the service center immediately if any of the conditions occurs. Please observe the radio device regulation of the local authority and turn off the power (put the device in Hibernation Mode) in places where radio transmission is not allowed. (Refer to the Hibernation Mode On/ Off Section in the Operation Section for detail.) This product contains a low-power laser component and is not intended to be used by a minor without adult supervision. When operate the laser function please use caution and never point the laser beam at a person or live animal, either directly or indirectly. Misusing the device or allowing minors to operate the device without adult supervision may violate the local law. 2 User Manual FCC Compliance (FCC ID: TDGVM200RF) The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment dose causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user should not modify or change this equipment without written approval from Toshiba. Modification could void authority to use this equipment. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter. CE This device complies with the essential requirements of the European Council Directive listed below: 99/5/EC Radio & Telecommunication Terminal Equipment (R&TTE) Directive Art.3.1a) EN 60950 Art.3.1b) EN 301 489 -1/-3 Art.3.2) EN 300 440 User Manual 3 Canada - Low Power License-exempt Radio Communication Device (RSS-210) a. Common Information Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. b. Operation in 2.4 GHz band To prevent radio interference to the licensed service, the device is intended to be operated indoors and installed outdoor is subject to licensing. PARTS IDENTIFICATION Channel Select Button A Transmission Status Light USB Connector Dongle Receiver Laser Pointer opening Channel Select Button B Battery Status Light Battery Charging Jack Laser Pointer Button Right Button Left Button E-Mouse Front View E-Mouse Rear View 4 User Manual Connector A Connector B USB Charging Cable USB Connector Transmission Status Light Channel Select Button A Channel Select Button B E-Mouse Right Button E-Mouse Left Button Plug into the USB port of the computer. Displays the wireless transmission status. Press down once to activate wireless channel selection. Hold down the Channel Select Button B and press down any of the Mouse Buttons once to set wireless channel. Performs the mouse right button function. Performs the Page Up function in the Presenter Mode Performs the mouse left button function Performs the Page Down function in the Presenter Mode Battery status indicator. Battery Low: Flashing Battery Charging: On Battery Full: Off (Remark A) Connects to the USB port to charge battery. Connects to the Battery Charging Jack to charge battery. Receptacle of Connector B. Battery Status Light Connector A Connector B Battery Charging Jack Laser Pointer Button Press down in the Presenter Mode to turn on the Laser Pointer. Remark A: When the battery power is extremely low the Battery Status Light will be turned off. User Manual 5 HARDWARE SETUP A. Charging Up the Battery For safety reasons, the battery was partially charged in the factory before packing. You may want to charge up the battery before using the device. 1. Insert Connector B of the USB Charging Cable into the Battery Charging Jack. 2. Insert Connector A of the USB Charging Cable into a USB port. When the battery is charging the Battery Status Light stays on. 3. Wait until the Battery Status Light turns off and remove the USB Charging Cable. The normal charging time should be 2 to 3 hours if a dedicated USB port is used. Charging time will be longer if a non-powered USB hub is used. (Remark B) 4. Repeat Steps 1 to 3 when the battery is flashing. You can keep on using the device during charging; however, the charging time will be extended. (Remark C) Remark B: Use a dedicated USB port or a powered USB Hub for fastest charging. Remark C: Lithium batteries do not have memory effect and can be partially charged. B. Installing the Device 1. Turn on your computer, if it is not already on. 2. Turn on your E-Mouse by pressing down both the left button and the right button for 10 seconds, if it is not already on. (Remark D) 3. Connect the Dongle Receiver to a USB port. A message "wireless pen mouse (2.4 GHz)" should appear on your computer screen. Allow the automatic set up process to complete and the messages to disappear. (Remark E) 4. Press down the Channel Select Button A on the Dongle Receiver once and the Transmission Status Light should start flashing. 5. Hold down the Channel Select Button B and press down any of the Mouse Buttons once and release. Wait for the Transmission Status Light to turn off, the installation is completed. 6. After the first successful installation, your Dongle Receiver and E-Mouse are permanently matched. You DO NOT need to repeat Steps 4 and 5 even when you take your E-Mouse to a different computer. 7. Repeat steps 4 and 5 to re-establish the transmission channel setting when needed. Remark D: For safety reasons, your E-Mouse was shipped with the power turned off. Please turn on the power before using it the first time. 6 User Manual Remark E: The series of messages will appear on each computer only once, when it receives the E-Mouse dongle the first time. OPERATION A. Adjusting the Mouse Speed Setting On Windows Computer: Click on Start/Settings/Control Panel from the root Window Frame to bring up the Control Panel and click on the Mouse icon to bring up the Mouse Setting Pane. Adjust the Speed Setting (using the slider) to the ¼ position from the slow end. Turn off the Acceleration function if it is available. Save the setting and exit the Control Panel. B. Using the Device 1. We suggest the first-time users to start with the "lap-style". That is, hold the E-Mouse like a pen and put your holding fist on your lap. 2. Keep the bottom of your fist on your lap and rest your elbow firmly against your body or a stable object. Use the device as if you were making a drawing on your lap to control the pointer movement on the computer screen. 3. Adjust the mouse speed setting as needed (Refer to subsection A of the OPERATION Section) to make the pointer control operation as comfortable as possible. 4. Once you are used to the operation, you can try the E-Mouse on the desk top or any other surfaces. C. 3-Stage Power Save Feature Your E-Mouse has a built-in 3-stage power save feature to maximize the battery usage. If it stays idle for more than a second, the LED dims and the E-Mouse goes into Stage One Power Save Mode. In Stage One, the motion sensor and the buttons remain operational. If the E-Mouse remains idle for 5 minutes in Stage One Power Save Mode, the LED starts flashing and the E-Mouse enters Stage Two Power Save Mode. In this mode, the motion sensor and the buttons remain operational. If the E-Mouse remains idle for 60 minutes in Stage Two Power Save Mode, the LED turns off and the E-Mouse enters Stage Three Power Save Mode. In this mode the motion sensor is turned off but the buttons remains operational. Remark F: Clicking the mouse button in any Power Save mode will bring the E-Mouse to the normal Mouse Mode immediately. D. Turning Power On/Off To turn off the power of the handheld unit, press down the Left Button and the Right Button at the same time for 10 seconds and wait for the Blue LED to turn off. User Manual 7 To turn on the power of the handheld unit, press down the Left Button and the Right Button at the same time for 10 seconds and wait for the Blue LED to turn on. You DO NOT have to reinstall the device or reset the communication channel between the handheld device and the receiver after turning off the power. E. Using the Laser Presenter Function Hold down the Channel Select Button B and press down the Laser Pointer Button once will put the E-Mouse into the Presenter Mode. In the Presenter Mode, the Blue LED is turned off, the Right Button becomes the Page Up button, and the Left Button becomes the Page Down button. Hold down the Channel Select Button B and press the Laser Pointer Button once again will switch the E-Mouse back to the Mouse Mode. PRODUCT CARE There are no user-serviceable parts in this product and you should not disassemble it under any circumstances without proper training/ authorization. Following the safety guidelines in the Safety Caution Section and this product should last for a long time. Occasional cleaning with a slightly damped soft towel on the outside will help keep its appearance in good condition. PRODUCT SPECIFICATIONS 2.4 GHz RF technology based rechargeable 2 button pen-style USB wireless optical mouse. Laser presenter with Page Up and Page Down functions. System Requirements Windows 2000 or XP with a USB port, Dongle Receiver USB 1.1 interface Dimension: 57mm x 18mm x 9mm 8 User Manual E-Mouse 1000 true optical Dot-Per-Inch resolution Blue LED 2 independent mouse buttons Built-in rechargeable Li battery 10 meter / 30 feet transmission distance Built-in 3-stage power-save feature Laser presenter with Page Up and Page Down functions. TROUBLESHOOTING Symptom System does not recognize the USB Receiver. Cause/Solution System does not meet product requirement. -> Upgrade system or move to a different computer. USB port is malfunction. -> Use a different USB port. Battery power is too low. -> Charge up the battery. E-Mouse is still in Presenter Mode. -> Wait for 10 seconds. E-Mouse is in Stage Three Power Save Mode. -> Click on the button once. Power is turned off -> Press down both buttons for 10 seconds to turn power on. Mouse Pointer does not move. Work surface is reflective. -> Use a non-reflective work surface. Battery power is too low. -> Charge up the battery. Communication setting on the E-Mouse may be changed. -> Reset the transmission setting. (See Hardware Setup, Sec. B) E-Mouse LED is off. -> Fix the LED problem. (Symptom 2) E-Mouse tilt angle too big. -> Make sure the focus line is in contact with the work surface. E-Mouse does not light up. User Manual 9 Symptom Battery does not charge. Cause/Solution Charging cable is not properly connected. -> Reconnect the cable. USB port is malfunction. -> Use a working USB port. Power does not turn on. Power does not turn off. Battery too low. -> Charge up the battery first. Mouse is in Presenter Mode. -> Hold down the Channel Select Button B and press the Laser Pointer Button once to switch back to the Mouse Mode. WARRANTY This product comes with a 1-year warranty on the rechargeable battery and a 1-year limited warr ...